Gold frame keycap clicker with switch in hand view.

Gold frame keycap clicker with switch front view.

Gold frame keycap clicker empty in hand view.

Spotto the monster in gold frame keycap clicker front view.

Spotto the monster in gold frame keycap clicker three quarter view.

Fangy the vampire after dinner keycap in gold frame clicker.

Grimsy the reaper keycap in gold frame clicker.

Wispy the beige ghost keycap in gold frame clicker.

Zibby the bright green alien keycap in gold frame clicker.

Gold Frame Keycap Clicker (Single)

$10.56NZD

Free Shipping over $99 NZD
Made in
Australia
Hand-Finished & Inspected
Secure Checkout

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Gold Frame Keycap Clicker (Single)

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Length: 43 mm
Width: 40 mm
Height: 16 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

A keycap deserves a frame if it is going to sit on your desk all year.

Same job as the plain base, considerably more occasion. The gleaming gold finish and ornate raised border make the cap sitting in the middle feel displayed rather than simply left there.

The switch inside is the real thing, so it presses like a keyboard key rather than a decoration. Put a skull in it and it looks like a tiny museum piece with a bad attitude.

Why You'll Love the Gold Frame

Catches the light on a shelf: the gleaming gold finish and raised details make the centrepiece feel properly framed.
Ready the moment it arrives: a Kailh Box clicky switch is already installed, so there is nothing to assemble.
Makes a loose keycap look deliberate: the border turns a spare cap into something you meant to display.
Change the face, keep the frame: caps swap by hand, so it can hold a pumpkin in October and something else in January.
Takes the caps you already own: standard MX mount, so spares from a keyboard build work in it too.

What You Get

1 x Gold Frame Keycap Clicker with 1 Kailh Box clicky switch fitted

Framed, mounted, and still fun to press.

Note: keycaps are sold separately. Fits standard single-stem MX-compatible keycaps. Compatible keycaps press-fit onto the switch and remain removable, so you can swap them whenever you feel like a change.