Plum keycap clicker base with switch in hand view.

Plum keycap clicker base with switch three quarter view.

Plum keycap clicker base empty in hand front view.

Plum keycap clicker base empty side view.

Boltsy the frankenstein keycap on plum clicker base three quarter view.

Fangy the vampire after dinner keycap on plum clicker base.

Lanty the pumpkin keycap on plum clicker base.

Spotto the monster keycap on plum clicker base.

Wispy the beige ghost keycap on plum clicker base.

Zibby the bright green alien keycap on plum clicker base.

Keycap Clicker Base (Single)

$7.92NZD

Free Shipping over $99 NZD
Made in
Australia
Hand-Finished & Inspected
Secure Checkout

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Keycap Clicker Base (Single)

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Length: 33 mm
Width: 27 mm
Height: 15 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

The little block that turns a keycap into a desk button.

On its own a keycap is just a shape. Push it onto this and it becomes something you can press: a real mechanical switch sits inside the base, so the cap goes down with a definite stop and springs straight back for the next one.

It takes any of the 10 Hollow Lane keycaps, and the standard MX keycaps you already own, so the spares from a keyboard build finally have somewhere to live.

Why You'll Love the Clicker Base

Nothing to buy or solder: a Kailh Box clicky switch comes already fitted, so it works the moment you put a cap on it.
A different face whenever you like: caps pull off and push on by hand, so one base can wear a new character each week.
Puts your spare keycaps to work: standard MX mount, so leftovers from a keyboard build fit straight in.
Low and flat on the desk: a wide, shallow base rather than a tall one, so it sits where you put it.
An easy place to start: add one compatible cap and you have a compact desk button ready to use.

What You Get

1 x Keycap Clicker Base with 1 Kailh Box clicky switch fitted

One switch. Endless faces.

Note: keycaps are sold separately. Fits standard single-stem MX-compatible keycaps. Compatible keycaps press-fit onto the switch and remain removable, so you can swap them whenever you feel like a change.