Fangy before-dinner and after-dinner vampire keycaps shown side by side.

Fangy the vampire before dinner keycap front view.

Fangy the vampire after dinner keycap front view.

Fangy the vampire before dinner keycap three quarter view.

Fangy the vampire after dinner keycap three quarter view.

The Fangy Pair

$6.99

Free Shipping over $59
Made in
Melbourne
Hand-Finished & Inspected
Secure Checkout

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at The Fangy Pair

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Product	Length	Width	Height
Fangy the Vampire Keycap (Before Dinner)	21 mm	19 mm	18 mm
Fangy the Vampire Keycap (After Dinner)	19 mm	21 mm	18 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Both of him. He maintains they are two different people.

Fangy before dinner is green, hungry and touchy about it. Fangy after dinner is pale, fed and entirely unwilling to discuss the green one who lives in the same room at 4 Hollow Lane. His post arrives addressed to both names. He signs for both without appearing to notice.

The joke only exists if you have the two of them. Sitting side by side on a four-slot holder, they do the work of a whole set with just two caps.

Why You'll Love the Fangy Pair

The pair is the punchline: one green vampire is a keycap, two is a running gag that everybody who sees your desk works out on their own.
The only housemate who comes in two: nine of the ten residents are one cap each. Fangy is the exception, and that is the entire reason this pair exists.
Two very different colours: sickly green next to pale and black, which reads clearly even from across a room.
Fits your own gear: both use an MX-style cross stem, tested here on a Kailh Box switch.

What You Get

1 x Fangy the Vampire (Before Dinner) 3D-printed keycap
1 x Fangy the Vampire (After Dinner) 3D-printed keycap

Two of him. Nobody at the house asks any more.

Note: keycaps do not click on their own. They need a mechanical switch to press against, either in one of our keycap holders or in your own keyboard.