Skip to content
Skip to product content

Fangy the Vampire Keycap (After Dinner) New!

$3.99
  • Free Shipping over $59

  • Made in
    Melbourne

  • Hand-Finished & Inspected

  • Secure Checkout

  • All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
  • Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
  • Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
  • Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
  • Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
  • Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Your Wiggly Stuff figures are built to last - with a little TLC!

  • Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
  • Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
  • No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
  • Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
  • Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
  • Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.
  • We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
  • Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
  • ⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
  • Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Fangy the Vampire Keycap (After Dinner)

Fangy the vampire after dinner keycap three quarter view.
Another angle from Wiggly HQ

The full story

Meet Fangy - considerably less green, and insisting he is a different person.

This is Fangy after dinner: fed, composed, cheerful, and completely unwilling to admit any connection to the green one who lives in the same room at 4 Hollow Lane. The rest of the house stopped arguing about it a long time ago. His post arrives addressed to both names and he signs for both without appearing to notice.

Everything the hungry version is not, right down to the tidy collar, and the contrast between the two of them is the whole reason to own both. Alone, he is the smartest looking cap in the set.

Why You'll Love It

  • Composed until you press him: in a holder there is a real clicky switch underneath, which undermines the dignity somewhat.
  • Better as a pair: stand him beside Fangy (Before Dinner) and the two-of-him running joke does the rest.
  • Your own switch works too: MX-style cross stem, tested on a Kailh Box.
  • Smart rather than spooky: pale and black reads as sharp, so he stays on the desk long after October.
  • Cheap enough to buy both of him: under four dollars each, so the pair comes in under eight.

What You Get

  • 1 x Fangy the Vampire (After Dinner) 3D-printed keycap

Signs for both names. Notices neither.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our keycap holders or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard.

Made to Swap

This keycap is designed to press-fit onto a compatible MX-style switch. We intentionally leave it unglued, so you can remove it and swap in another compatible keycap later.

Cart

Spend $59 more for free shipping.

Your cart is currently empty