Wrappy the mummy keycap three quarter view.

Wrappy the mummy keycap on plum clicker base.

Wrappy the mummy keycap in gold frame clicker.

Wrappy the mummy keycap in Hollow Lane single clicker house.

Wrappy the mummy keycap underside MX stem.

Plum four slot base Zibby Kernie Spotto Wrappy group front view.

Hollow Lane four slot house Fangy pair Wrappy Lanty group view.

Hollow Lane four slot house Wrappy Spotto Kernie Zibby group view.

Wrappy the Mummy Keycap New!

$3.99

Free Shipping over $59
Made in
Melbourne
Hand-Finished & Inspected
Secure Checkout

All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Wrappy the Mummy Keycap

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Length: 19 mm
Width: 20 mm
Height: 17 mm

Quality & Process

All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Meet Wrappy - forty minutes to get ready, and still first out the door.

Nobody at 4 Hollow Lane has worked out how Wrappy does it. Forty minutes in the bathroom, every single time, no exceptions, and yet she is always standing by the front door with her bag on before anybody else has found their keys. Grimsy has tried to build the timing into the roster and given up twice.

Wound in soft bone-coloured layers with two dark eyes peering out, she has more surface going on than anything else at the address. In a holder she is a small bandaged button that your fingertip keeps returning to.

Why You'll Love It

Texture first, click second: the printed bandage ridges give your fingertip something to find, and in a holder a real clicky switch answers underneath.
Fits MX-style switches: tested here on a Kailh Box.
Goes with any desk: soft bone sits quietly beside both light and dark keycaps instead of fighting them.
Spooky without being grim: a mummy reads as friendly in a way a skull does not, if that matters to the person receiving her.
Small spend, easy add: under four dollars, with nine housemates to go looking for afterwards.

What You Get

1 x Wrappy the Mummy 3D-printed keycap

Forty minutes. Every time. Still first.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our keycap holders or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard.

Made to Swap

This keycap is designed to press-fit onto a compatible MX-style switch. We intentionally leave it unglued, so you can remove it and swap in another compatible keycap later.