Hollow Lane single clicker house with switch front view.

Hollow Lane single clicker house with switch in hand view.

Hollow Lane single clicker house empty in hand front view.

Hollow Lane single clicker house empty with roof side view.

Fangy before dinner in Hollow Lane single clicker house front view.

Fangy before dinner in Hollow Lane single clicker house three quarter view.

Boltsy the frankenstein keycap in Hollow Lane single clicker house.

Grimsy the reaper keycap in Hollow Lane single clicker house.

Wispy the beige ghost keycap in Hollow Lane single clicker house.

Zibby the bright green alien keycap in Hollow Lane single clicker house.

Hollow Lane Clicker House (Single) New!

$9.73SGD

Fast Shipping
Made in
Australia
Hand-Finished & Inspected
Secure Checkout

All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Hollow Lane Clicker House (Single)

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Length: 35 mm
Width: 27 mm
Height: 19 mm

Quality & Process

All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

A tiny haunted house with one room, and a button where the tenant goes.

A black house with a purple bricked wall, a round window and a single keycap-sized space in the middle. Drop a cap in and the house has a resident. Underneath that resident is a real mechanical switch, so pressing down on the roof does exactly what your hand wants it to do.

It is a display piece that happens to work as a fidget, which is a rarer combination than it sounds. It also happens to be the building our Halloween keycap characters live in, if you decide to collect them.

Why You'll Love It

Ready to press out of the box: a Kailh Box clicky switch comes fitted, with a firm stop and a fast return.
Nothing painted on: the black shell and purple brickwork are printed in two separate filaments, so the colour runs right through.
Rotate the tenant: caps lift out and push in by hand, so the resident changes whenever you feel like it.
Earns a spot on the shelf: it looks like a model building and still does something when you reach for it.
The cheaper of the two houses: the single-room version if the four-slot is more building than you need.

What You Get

1 x Hollow Lane Clicker House (Single) with 1 Kailh Box clicky switch fitted

One room. Ten applicants.

Note: keycaps are sold separately. Fits standard single-stem MX-compatible keycaps.

Made to Swap

Compatible keycaps press-fit onto the switch. We intentionally leave them unglued, so you can remove and swap keycaps whenever you feel like a change.