Nutmeg the Santa puppy keycap in a red Santa hat, paws on a spotty red present, front view

Nutmeg the Santa puppy Christmas keycap with rosy cheeks, front view

Nutmeg the Santa puppy keycap from a low front angle

Nutmeg the Santa puppy keycap, three-quarter view from the left

Nutmeg the Santa puppy keycap, three-quarter view from the right

Back of Nutmeg the Santa puppy keycap, showing the Santa hat and floppy ears

Nutmeg the Santa puppy keycap from behind, slightly angled

Nutmeg Santa puppy keycaps sitting in red and white gift box clicker bases

Nutmeg with the pudding, elf and snowman keycaps in a red four-slot gift box base

Nutmeg the Santa Puppy Keycap New!

$4USD

Fast Shipping
Made in
Australia
Hand-Finished & Inspected
Secure Checkout

Build a clicker with Nutmeg Pick a base, fill the slots, add a keyring if it's coming along.

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Nutmeg the Santa Puppy Keycap

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Option	Length	Width	Height
Nutmeg the Santa Puppy Keycap	18 mm	18 mm	29 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Meet Nutmeg - the puppy who never takes the Santa hat off.

Nutmeg put the Santa hat on one December and simply never took it off. He sits with his paws hooked over the edge of his spotty red present like he is waiting to be let out, rosy cheeks and all. Last year he ate one corner off the advent calendar. Nobody has asked him about it directly.

Tuck him into one of our gift box clicker bases and he is a desk buddy ready for a pat on the head when the day needs one. On a keyboard of your own he makes even the backspace key look friendly.

See Them in Action

Why You'll Love Nutmeg

A face that makes people smile: floppy ears, a Santa hat and a slightly guilty expression.
A pat on the head between emails: in a gift box base he ducks down when pressed and bounces straight back up, ears and all.
Or let him run a key: MX-style cross stem, tested here on a Kailh Box.
The easy gift for dog people: small, cute and very hard to say no to.
Collect the whole box: he shares the gift box under the tree with seven other Christmas characters.

What You Get

1 x Nutmeg the Santa Puppy 3D-printed keycap

Hat stays on. Questions stay unasked.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our clicker bases or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard. The cap press-fits onto a compatible switch and is intentionally left unglued so it can be removed or swapped.