Spotto the monster keycap three quarter view.

Spotto the monster keycap on plum clicker base.

Spotto the monster in gold frame keycap clicker front view.

Spotto the monster in gold frame keycap clicker three quarter view.

Spotto the monster keycap in Hollow Lane single clicker house.

Spotto the monster keycap underside MX stem.

Hollow Lane four slot house Kernie Zibby Spotto Fangy group front view.

Plum four slot base Boltsy Spotto Lanty Fangy group front view.

Plum four slot base Zibby Kernie Spotto Wrappy group front view.

Spotto the Monster Keycap New!

$3.88SGD

Fast Shipping
Made in
Australia
Hand-Finished & Inspected
Secure Checkout

All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Spotto the Monster Keycap

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Length: 19 mm
Width: 19 mm
Height: 18 mm

Quality & Process

All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Meet Spotto - too big for the furniture, and sorry about it forty times a day.

Spotto does not fit anything at 4 Hollow Lane. Not the couch, not the good chair, not the doorway to the back room. He apologises constantly and indiscriminately, including to the furniture itself, which the others have decided is the most Spotto thing about him. Nobody has asked him to stop, because it would only produce another apology.

Teal with hot pink spots and a great deal of eye, he is the biggest personality at the address on the smallest possible scale. In a holder he is a bright button that catches a hand going past.

Why You'll Love It

A big friendly target: in a holder he sits over a real clicky switch, and that broad spotted face is an easy thing for a wandering finger to find.
Cross stem, same as a keycap: tested on a Kailh Box switch, so your own build is worth a look.
Hard to ignore: teal and hot pink together are the loudest thing you can put on a desk this small.
Friendly rather than frightening: the easy choice for someone who wants the fun without the graveyard.
An easy extra to add on: under four dollars, so he can go in alongside something bigger.

What You Get

1 x Spotto the Monster 3D-printed keycap

Said sorry to a chair this morning. Meant it.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our keycap holders or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard.

Made to Swap

This keycap is designed to press-fit onto a compatible MX-style switch. We intentionally leave it unglued, so you can remove it and swap in another compatible keycap later.