Skip to content
Skip to product content

Keycap Clicker Base (Four-Slot) New!

$12USD
  • Fast Shipping

  • Made in
    Australia

  • Hand-Finished & Inspected

  • Secure Checkout

  • All our models are printed with multiple walls and increased infill using high-quality, non-toxic PLA for maximum strength and safety.
  • Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal -and make every piece uniquely yours.
  • Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
  • Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
  • Each figurine is carefully packaged with protective packaging to ensure it arrives in perfect condition.
  • Please inspect your figurine upon arrival. If you have any concerns, contact us before leaving feedback.

Your Wiggly Stuff figures are built to last - with a little TLC!

  • Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
  • Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
  • No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
  • Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
  • Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
  • Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.
  • We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
  • Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
  • ⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
  • Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Keycap Clicker Base (Four-Slot)

Plum four slot base Boltsy Spotto Lanty Fangy group front view.
Another angle from Wiggly HQ

The full story

Four switches, four caps, one block.

One cap is a fidget. Four in a row is a habit. Each slot has its own mechanical switch underneath, so you can run a finger across all four, work left to right, or hammer the same one for ten minutes while you think about something else.

Four spaces also means four of our Halloween keycap characters get a room at once, which is the whole problem with a house of ten. Choose your four. Change them whenever you like.

Why You'll Love It

  • Four different ways to fidget: every slot has its own Kailh Box clicky switch, so each one presses independently of the others.
  • Roll a finger across the set: four in a row lets you run left to right instead of pressing the same thing over and over.
  • Four favourites on show at once: pick the four you like most and swap them out by hand whenever the lineup goes stale.
  • Mix ours with yours: the four slots take our characters and your own MX caps side by side.
  • Better value than buying singles: four fitted switches for less than the cost of four single bases.

What You Get

  • 1 x Four Slot Keycap Clicker Base with 4 Kailh Box clicky switches fitted

Four rooms. Ten housemates. Good luck.

Note: keycaps are sold separately. Fits standard single-stem MX-compatible keycaps.

Made to Swap

Compatible keycaps press-fit onto the switch. We intentionally leave them unglued, so you can remove and swap keycaps whenever you feel like a change.

Cart

Spend $59 USD more for free shipping.

Your cart is currently empty