Red and white single gift box clicker bases, each holding a red present keycap with a yellow bow

Two single gift box clicker bases holding Santa puppy keycaps

Two single gift box clicker bases holding Christmas pudding keycaps

Two single gift box clicker bases holding green elf keycaps

Two single gift box clicker bases holding snowman keycaps

White and red single gift box bases with green present keycaps

Single gift box bases holding white present keycaps with red bows

White single gift box base holding a spotted present keycap

Empty red single gift box clicker base with a white ribbon, front view

Empty red single gift box clicker base, angled view showing the keycap socket

Red single gift box clicker base from the side, showing the ribbon loop

Red single gift box base with a clicky switch fitted inside

Red single gift box base with a switch fitted, angled view

Red single gift box clicker base held between finger and thumb

Empty white single gift box clicker base with a red ribbon

Empty white single gift box clicker base, angled view

White single gift box base with a clicky switch fitted inside

White single gift box base with a switch fitted, angled view

White single gift box base with a switch, side view showing the ribbon

White single gift box base with a switch, held in fingers to show its size

Empty white single gift box clicker base held in a hand

Christmas Gift Box Clicker Base (Single) New!

$5.99

Colour:

Red

White

Free Shipping over $59
Made in
Melbourne
Hand-Finished & Inspected
Secure Checkout

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Christmas Gift Box Clicker Base (Single)

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Option	Length	Width	Height
Red	24 mm	30 mm	19 mm
White	24 mm	30 mm	19 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

The Christmas present you open by pressing it.

A small gift box with a ribbon wrapped all the way round and an opening on top just the size of a keycap. Drop in one of our Christmas characters and the present appears to be opening itself. There is a keyboard switch hidden in the bottom of the box, so whoever is on top goes down with a click every time you press them.

It looks right beside the keyboard and just as right on the shelf with the Christmas cards. It is also the same gift box our eight Christmas keycap characters call home.

Choose your favourite colour:

Red: red box, white ribbon. The classic.
White: white box, red ribbon. A lighter, snowier look.

See Them in Action

Why You'll Love the Single Gift Box

Nothing to install: the switch comes fitted, so it clicks from the moment a cap goes on.
A present that stays wrapped: all the fun of opening one, every time you press it.
Change who is inside: the cap on top pulls off and swaps over by hand, so the gift can change daily.
Fits any MX-style cap: our Christmas characters, our Halloween housemates or your own keycaps.
An easy little gift: add a keycap and it is a Kris Kringle present that is still wrapped.

What You Get

1 x Christmas Gift Box Clicker Base (Single) in your chosen colour, with 1 Kailh Box clicky switch fitted

Opened a hundred times a day. Still wrapped.

Note: keycaps are sold separately. Fits standard single-stem MX-compatible keycaps. Compatible keycaps press-fit onto the switch and remain removable, so you can swap them whenever you feel like a change.