Figgy the Christmas pudding keycap with white icing and holly, front view

Figgy the Christmas pudding keycap from a low front angle

Figgy the Christmas pudding keycap, three-quarter view from the left

Figgy the Christmas pudding keycap, three-quarter view from the right

Back of Figgy the Christmas pudding keycap, showing the icing and holly

Figgy Christmas pudding keycaps sitting in red and white gift box clicker bases

Figgy with the elf, snowman and Santa puppy keycaps in a red four-slot gift box base

Figgy the Christmas Pudding Keycap New!

$3.99

Free Shipping over $59
Made in
Melbourne
Hand-Finished & Inspected
Secure Checkout

Build a clicker with Figgy Pick a base, fill the slots, add a keyring if it's coming along.

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Figgy the Christmas Pudding Keycap

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Option	Length	Width	Height
Figgy the Christmas Pudding Keycap	19 mm	19 mm	27 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Meet Figgy - the Christmas pudding who has been resting since March.

Figgy was made in March and has been resting in the back of a cupboard ever since, which he will tell you about at length if you let him. He came out for December with his icing poured, holly on top and a very serious expression about the whole thing. Mint has asked not to sit next to him. He has not taken it personally. Much.

Give him a gift box clicker base and he settles in like it is his spot at the table. On a keyboard of your own he makes every day feel a bit like the afternoon after Christmas lunch.

See Them in Action

Why You'll Love Figgy

The most Christmas thing in the box: nothing says December quite like a pudding with holly on top.
A press with some weight to it: in a gift box base he lands like a spoon on a full bowl, then rises again for seconds.
Keyboard-ready: MX-style cross stem, tested here on a Kailh Box.
A gift for whoever makes the pudding: a small nod to the family cook that will not go stale.
Good company: he shares the big gift box with seven other Christmas characters, whatever Mint says.

What You Get

1 x Figgy the Christmas Pudding 3D-printed keycap

Nine months of resting. Ready now.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our clicker bases or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard. The cap press-fits onto a compatible switch and is intentionally left unglued so it can be removed or swapped.