Mint the white present keycap with a red bow

Mint the white present Christmas keycap, angled view

Mint white present keycaps sitting in red and white gift box clicker bases

Mint with other present keycaps in a white four-slot gift box base

Mint the White Present Keycap New!

$3.99

Free Shipping over $59
Made in
Melbourne
Hand-Finished & Inspected
Secure Checkout

Build a clicker with Mint Pick a base, fill the slots, add a keyring if it's coming along.

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Mint the White Present Keycap

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Option	Length	Width	Height
Mint the White Present Keycap	19 mm	19 mm	18 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Meet Mint - the neatest present under the tree.

Mint keeps her paper smooth and her corners sharp, and she will remind you, unprompted, that she was wrapped first. She has asked twice not to be put next to the pudding, on account of the crumbs. Her red bow sits exactly in the middle, which Sprig finds quietly unbearable.

Set her in one of our gift box clicker bases for a tidy little button on a desk that likes things just so. Or put her on a keyboard of your own, where she stays the one key that always looks freshly wrapped.

See Them in Action

Why You'll Love Mint

Festive without the noise: white with a single red bow suits a minimal desk as well as a full Christmas display.
Stands out on dark keyboards: she is easy to find on a black board without looking down.
Something to press while you think: in a gift box base she goes down neatly and comes back up exactly where she started, corners intact.
Or on your own keyboard: MX-style cross stem, tested here on a Kailh Box.
A gift for the person who notices details: small, neat and wrapped better than anything else under the tree.

What You Get

1 x Mint the White Present 3D-printed keycap

Wrapped first. Will mention it.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our clicker bases or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard. The cap press-fits onto a compatible switch and is intentionally left unglued so it can be removed or swapped.