Jingle the elf keycap in a green and red elf hat, front view

Jingle the elf Christmas keycap, three-quarter view from the left

Jingle the elf keycap, three-quarter view from the right

Back of Jingle the elf keycap, showing the hat bobble

Jingle elf keycaps sitting in red and white gift box clicker bases

Jingle with the pudding, snowman and Santa puppy keycaps in a red four-slot gift box base

Jingle the Elf Keycap New!

$3.99

Free Shipping over $59
Made in
Melbourne
Hand-Finished & Inspected
Secure Checkout

Build a clicker with Jingle Pick a base, fill the slots, add a keyring if it's coming along.

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

Meet the wiggly details

A closer look at Jingle the Elf Keycap

Another angle from Wiggly HQ

Quick facts

At a glance

Approximate Product Dimensions (mm)

Option	Length	Width	Height
Jingle the Elf Keycap	19 mm	19 mm	28 mm

Quality & Process

We 3D-print our models in PLA, with wall and infill settings suited to each design.
Each Wiggly Stuff figurine is 3D-printed and hand-finished, so slight imperfections, visible layer lines, colour shifts in the filament, and tiny variations are normal - and make every piece uniquely yours.
Gradient and rainbow colour patterns occur randomly and may vary from batch to batch.
Actual filament colours may vary slightly from what you see on screen due to dye-lot differences and monitor settings.
Each figurine is carefully packaged with protective packaging to help protect it in transit.
Please inspect your figurine on arrival. If you have any concerns, contact us and we’ll help.

Product Care

Your Wiggly Stuff figures are built to last - with a little TLC!

Keep cool: PLA softens above ~60 °C (≈ 140 °F). Avoid leaving your figurine in direct sun, inside hot cars, or near heaters.
Gentle cleaning only: Rinse under lukewarm, soapy water. Use a soft brush or toothpick to clear any dust or debris from tight spots.
No dishwashers or ovens: High heat or harsh detergents can warp or weaken the plastic.
Handle with care: These figures are flexible but not indestructible. Don’t bend or twist parts beyond their normal range, and avoid strong lateral pressure.
Glued parts: Some figures may include glued parts or small attached pieces. If a piece loosens or detaches, it can usually be reattached with a small amount of standard super glue. Let the glue fully dry before handling again.
Display tip: For best colour retention, keep your figure out of prolonged UV exposure - indoors on a shelf or in a display case is ideal.

Safety

We do our absolute best to ensure our prints are free from sharp edges, but minor imperfections may occur - please inspect each piece before handling them.
Some items may contain glued parts or small attached pieces. These may loosen or detach if dropped, bent, chewed, pulled, or handled roughly.
⚠️ Choking Hazard: Wiggly Stuff figurines contain small parts and are not suitable for children under 3 years. Always supervise young children during play and use your discretion when gifting these items.
Not food-safe and not intended for live animals or aquarium use.

Licensed Seller – Model by Puffy Puff

Dreamed up in London, wiggled into shape in Melbourne

The full story

Meet Jingle - the elf who ties bows nobody asked for.

Jingle ties every bow in the house, including the ones that were already tied. He retied Sprig's bow straight down the middle, and Sprig put it back the way it was before lunch. Neither of them has mentioned it since. Jingle is already looking at Mint's.

Station him in one of our gift box clicker bases and he is a busy little button for a busy desk. On a keyboard of your own he is the key that gets things done, whether or not they needed doing.

See Them in Action

Why You'll Love Jingle

All Christmas, all business: the green hat and big grin bring the workshop feeling to any desk.
Made for fiddly hands: in a gift box base he snaps down like a bow pulled tight and springs straight back for another.
Keyboard-ready: MX-style cross stem, tested here on a Kailh Box.
A gift for the organised one: perfect for whoever does all the wrapping every year.
One of eight: he lives in the big gift box with the presents he keeps trying to retie.

What You Get

1 x Jingle the Elf 3D-printed keycap

Every bow. Every time.

Note: a keycap on its own does not click. It needs a mechanical switch to press against, either in one of our clicker bases or in your own keyboard. Caps are roughly 19 x 19mm across and between 16 and 19mm tall depending on the character, with an MX-style cross stem. Check your switch type and key spacing before ordering if you plan to use one on a keyboard. The cap press-fits onto a compatible switch and is intentionally left unglued so it can be removed or swapped.